Chrome-plated racing exhaust with attached silencer suitable for various Puch mopeds / mopeds with a straight outlet.
This tuning exhaust delivers plenty of power and is also visually stunning.
The rearmost end of the resonance body is fitted with a screw. Two additional screws with different holes are included in the scope of delivery.
These can be replaced. This changes the exhaust back pressure and therefore the performance of the silencer.
This gives you an exhaust for the lower, middle and upper speed range all in one.
You can find more racing pipes in the accessories section.
Branded product from the Portuguese manufacturer TECNO.
| Manufacturer | TECNO |
| Material | Steel, Aluminum |
| Surface | chrome-plated |
| Color | Chrome |
| Total length | 900 mm |
| Ø Silencer | 60 mm |
| Ø Internal connection | 24 mm |
| Ø Flame tube outside | 28 mm |
| Exhaust type | Cone / double cone |
| Number of fixing points | 3 pcs |
| Puch |
Ratings
Accessories & related products
swiing® ingenious gasket outlet 28 mm graphite
Thickness: 3 mm · Manufacturer: swiing® ingenious parts · Material: Graphite / Graphite · Ø inside: 27.4 mm · Reinforced: No · Place of use: Exhaust · Ø outlet inside: 28 mm · Hole spacing outlet: 42.5 mm · Ø screw holder: 6.6 mm · Area of application: Tuning
EUR 9.15
Hot 
HOMOET exhaust P6 blank | Puch
Manufacturer: HOMOET · Material: Steel · Surface: raw · Surface: varnished · Color: gray · Mounting type: Tab · Ø Silencer: 50 mm · Ø outside: 88 mm · Total length: 900 mm · Number of fixing points: 2 pcs · Ø Flame tube outside: 28 mm · Exhaust type: Cone / double cone · Flame tube attachment: Stud bolts & nuts
EUR 351.60
Not in stock
Moped fans also bought
swiing® ingenious pull starter Bosch / Ducati | Puch E50
Material: Plastic · Material: Steel · Color: Chrome · Color: black-matt · Total length: 160 mm · Height: 88 mm · Number of fixing points: 2 pcs · Manufacturer: swiing® ingenious parts · Ø outside: 130 mm · Surface: chrome-plated · Ignition system: BOSCH · Ignition system: DUCATI · Width: 150 mm · Hole spacing: 137.5 mm
EUR 185.00
Not in stock
Not so nice 
Road Master 2.25 x 17" F-323 4.P.R. Allround
Inventory-managed: No · Manufacturer: Road Master · Tire width: 2.25 " · Color: black · Width: 2 1/4 " · Wheel size: 17 " · Old designation: 21 x 2.25 " · Speed index: B = 50 km/h · Load capacity index: 39 = 136 kg · Profile type: F-323 4 P.R. · Tire type: Allround · White wall: No · Tubeless (yes/no): Tubetype TT (requires hose)
EUR 40.10
swiing® revival brake support bolt short Inox | Puch Maxi, Supermaxi
Ø External head: 14 mm · Manufacturer: swiing® revival parts · Material: Chrome steel (colloquially known as stainless steel) · Number of components: 3 pcs · Total length: 32 mm · Drive: Outer edge · Width across flats: 13 mm · Width across flats: 17 mm · Thread type: MF10x1 (fine pitch thread) · Shank: Yes · Shank length: 9.5 mm · Ø shaft: 9.8 mm · Thread length: 13 mm · Area of application: Standard
EUR 15.90
Hot
Jammer racing clutch special 65 ccm and more | Puch E50
Material: Steel · Manufacturer: Jammer · Ø outside: 92.5 mm · Material addition: Steel · Recording type: Cone mounting · Number of jaws: 3 pcs · Number of springs: 3 pcs · Thickness: 19 mm · Area of application: High End · Area of application: MX · Area of application: Racing · Area of application: Tuning
EUR 234.40
Not in stock
Hot
swiing® ingenious 15 mm carburetor camouflaged | Puch
Manufacturer: swiing® ingenious parts · Material: Aluminum · Camouflaged: Yes · Component group Carburetor: Carburetor complete · Width: 50 mm · Carburetor type: SRE · Height: 95 mm · Nominal diameter: 15 mm · Total length: 66 mm · Ø Inside entrance: 15 mm · Ø Internal connection: 20 mm · Ø Output inside: 15 mm · Ø Air filter connection: 20 mm · Ø fuel hose connection: 6 mm · Mixed oil connection: No · Mounting type: Plug connection clamped · Vacuum connection: No · Choke control: Hand choke · Nozzle thread: M3.5x0.6 (standard thread) · Nozzle block: 2.17 · Nozzle size: 62 · Clamping screw torque (max.): 4 N/m · Area of application: Tuning · Puch OEM number: 349.1.15.100.0 · Puch OEM number: 349.2.15.800.0 · Puch OEM number: 349.4.15.500.0 · Puch OEM number: 349.4.15.000.0 · Puch OEM number: 349.4.15.300.0 · Puch OEM number: 349.6.15.400.0 · Puch OEM number: 349.7.15.700.0 · Puch OEM number: 349.8.15.400.0 · Puch OEM number: 349.9.15.300.0
EUR 98.60
Hot
swiing® revival 12 mm carburetor "Original" | Puch
Manufacturer: swiing® revival parts · Material: Aluminum · Camouflaged: No · Component group Carburetor: Carburetor complete · Color: gray · Width: 50 mm · Carburetor type: SRE · Height: 108 mm · Nominal diameter: 12 mm · Total length: 65 mm · Ø Inside entrance: 12 mm · Ø Internal connection: 20 mm · Ø Output inside: 12 mm · Ø Air filter connection: 20 mm · Ø fuel hose connection: 6 mm · Mixed oil connection: No · Mounting type: Plug connection clamped · Vacuum connection: No · Choke control: Hand choke · Nozzle thread: M3.5x0.6 (standard thread) · Nozzle block: 2.15 · Nozzle size: 52 · Clamping screw torque (max.): 4 N/m · Area of application: Standard · Puch OEM number: 349.6.15.400.0 · Puch OEM number: 349.7.15.700.0
EUR 86.30
Collection only possible with online purchase and appointment.
