Socket axle set with closed groove ball bearings (Ø 29 mm) for front cast hubs (Leleu) on your Puch moped / moped.
The threaded shaft set consists of a 165 mm long wheel axle, two special ball bearings and all required nuts and spacers.
The wheel axle set works with Leleu front wheel hubs, which are installed in cast rims.
The cable ties show you where to mount what:
- Red marking: wheel hub
- Green marking: Brake anchor plate
- Yellow marking: Replacement disk for the speedometer drive (the disk is omitted if a drive is fitted)
- Blue marking: fork leg
Note: When installing the ball bearings, it is important to note that the long spacer bushing must be clamped between the two ball bearings to ensure that the two bearings press against the bushing with the inner ring. If this is not observed, the ball bearings will inevitably jam.
| Ø inside | 12 mm |
| Ø outside | 29.02 mm |
| Manufacturer | swiing® ingenious parts |
| Ball bearing closed | Yes |
| Material | Steel |
| Surface | galvanized (blue) |
| Width | 34.5 mm, 6.6 mm, 11 mm, 2.7 mm |
| Height | 9.9 mm, 5.9 mm |
| Total length | 165 mm |
| Ø shaft | 11.95 mm |
| Shank length | 74.5 mm |
| Thread length | 50 mm, 40.5 mm |
| Width across flats | 19 mm |
| Thread type | MF12x1 (fine pitch thread) |
| Puch |
Accessories & related products
Hot 
swiing® ingenious wheel axle with bearing conversion kit spoke hub front | Puch
Ball bearing closed: Yes · Manufacturer: swiing® ingenious parts · Material: Steel · Surface: galvanized (blue) · Width: 2.7 mm · Width: 6.6 mm · Width: 11 mm · Ø inside: 12 mm · Width: 35.7 mm · Height: 5.9 mm · Height: 9.9 mm · Total length: 165 mm · Ø shaft: 11.95 mm · Ø outside: 29.02 mm · Thread type: MF12x1 (fine pitch thread) · Shank length: 74.5 mm · Width across flats: 19 mm · Thread length: 40.5 mm · Thread length: 50 mm
EUR 47.70
Hot
swiing® ingenious wheel axle with bearing conversion kit rear spoke hub | Puch
Ø inside: 12 mm · Ball bearing closed: Yes · Manufacturer: swiing® ingenious parts · Material: Steel · Surface: galvanized (blue) · Diameter: 29 mm · Total length: 190 mm · Ø shaft: 19 mm · Ø outside: 29 mm · Thread type: MF12x1 (fine pitch thread) · Shank length: 100 mm · Width across flats: 19 mm · Thread length: 29 mm · Thread length: 53 mm
EUR 47.70
swiing® ingenious wheel bearing 12/29/9 spoke & cast rim | Puch Maxi
Bearing type: Deep groove ball bearing · Bearing cage: Sheet steel cage ball-guided · Inner ring width: 9 mm · Ball bearing closed: Yes · Manufacturer: swiing® ingenious parts · Dust protection type: 2RS - NBR contact seal on both sides · Bearing clearance: CN (standard) · Material: Plastic · Material: Steel · Width: 9 mm · Ø inside: 12 mm · Ø outside: 29.02 mm
EUR 10.90
GPO speedo drive 17" with lugs 12 mm axle | Puch Maxi S / N, X30 Sport NS / NL, NG-2AH, X30 Velux
Manufacturer: GPO · Place of use: left · Place of use: right · Ø axle: 12 mm · Material: Aluminum · Ø outside: 41 mm · Wheel size: 17 " · 4-edge speedometer cable: 1.8 mm · 4-edge speedometer cable: 2.6 mm · Thread type: MF10x1 (fine pitch thread) · Ø mounting hole: 12 mm
EUR 34.20
Explore categories from Hub & axle
Moped fans also bought
Hot
Fuel tap horizontal M12x1 (with union nut) outgoing at the bottom
Manufacturer: GPO · Possible lever positions: open / closed / reserve · Material lever: Metal · Filter type: Plastic net · Ø fuel hose connection: 6 mm · Mounting type: Union nut · Installation direction: horizontal / horizontal · Outlet direction: below · Thread type: MF12x1 (fine pitch thread) · Spare tube shape: curved · Reserve level: 70 mm
EUR 12.10
NTN wheel bearing 12/28/8 rear cast hub Leleu | Puch Maxi
Bearing type: Deep groove ball bearing · Bearing cage: Sheet steel cage ball-guided · Ø inside: 12 mm · Stock number: 6001 · Inner ring width: 12 mm · Manufacturer: NTN · Ball bearing closed: Yes · Dust protection type: 2RS - NBR contact seal on both sides · Bearing clearance: CM (special/noise-reduced) · Groove ring: No · Material: Plastic · Material: Steel · Area of application: Standard · Width: 8 mm · Ø outside: 28 mm
EUR 7.25
Hot
swiing® revival wheel axle LELEU & Grimeca wheel hub cast wheel rear | Puch
Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Total length: 185 mm · Ø shaft: 11.9 mm · Ø outside: 11.8 mm · Thread type: MF12x1 (fine pitch thread) · Shank length: 100 mm · Width across flats: 19 mm · Thread length: 26 mm · Thread length: 52.5 mm
EUR 18.30
Hot
swiing® ingenious wheel axle with bearing conversion kit rear spoke hub | Puch
Ø inside: 12 mm · Ball bearing closed: Yes · Manufacturer: swiing® ingenious parts · Material: Steel · Surface: galvanized (blue) · Diameter: 29 mm · Total length: 190 mm · Ø shaft: 19 mm · Ø outside: 29 mm · Thread type: MF12x1 (fine pitch thread) · Shank length: 100 mm · Width across flats: 19 mm · Thread length: 29 mm · Thread length: 53 mm
EUR 47.70
Hot
Inner cable set automatic | Puch E50
Manufacturer: Made in Germany · Material: Steel · Quantity: 4 pcs · Ø Stranded wire: 1.25 mm · Ø Stranded wire: 1.5 mm · Ø Stranded wire: 1.8 mm · Total length: 1600 mm · Total length: 2200 mm · Nipple shape: Barrel (transverse) · Nipple shape: Cylinder · Nipple shape: Pears
EUR 12.10
swiing® revival wheel axle set LELEU wheel hub cast wheel rear | Puch
Ø inside: 12 mm · Ø outside: 28 mm · Ø outside: 29 mm · Manufacturer: SKF · Ball bearing closed: Yes · Manufacturer: swiing® revival parts · Total length: 190 mm · Width: 8 mm · Width: 9 mm · Material: Steel · Surface: galvanized (blue)
EUR 37.90
SKF 6001 2RSH Ball bearing 12/28/8
Bearing type: Deep groove ball bearing · Bearing cage: Sheet steel cage ball-guided · Ø inside: 12 mm · Stock number: 6001 · Inner ring width: 8 mm · Manufacturer: SKF · Ball bearing closed: Yes · Dust protection type: 2RSH - NBR contact seal on both sides · Bearing clearance: CN (standard) · Width: 8 mm · Ø outside: 28 mm
EUR 15.80
Working late? Evening hours on Thursday until 20:00
