Replica wire spoke hub made of aluminum with pressed-in bearings for the rear wheel of various mopeds, mopeds and small motorcycles.
Note: The hub is at the limit of tolerances in the area of the brake drum and sprocket mount. The function is just about guaranteed, but you shouldn't expect too much.
The bearings installed are also not of particularly high quality.
You can find suitable add-on parts for the rear hub such as brake pads, clamping screws etc. in the accessories section.
Details
| Material | Aluminum |
| Area of application | Standard, Custom |
| Ø drum | 80 mm |
| Surface | blank |
| Ø inside | 30 mm |
| Ø axle | 12 mm |
| Ø Receptacle | 93 mm |
| Number of spoke holes | 36 pcs |
Suitable for the following models
| Puch |
Accessories & related products
Brake cable Ø 1.8 mm x 220 cm (pear-shaped nipple)
Ø nipple: 3.5 mm · Ø nipple: 6 mm · Manufacturer: Made in Germany · Area of application: Standard · Material: Steel · Surface: galvanized (blue) · Ø Stranded wire: 1.8 mm · Nipple shape: Pears · Cable length: 2200 mm · Nipple length: 10 mm · Number of components: 1 pcs
EUR 2.95
swiing® revival rear brake anchor plate | Puch Maxi S, X30 NG
Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Ø outside: 91 mm · Ø shaft: 10 mm · Ø External brake pads: 80 mm · Ø bore: 12.2 mm · Total length: 187 mm · Ø axle: 12 mm · Wide cam holder: 12 mm · Brake lever length (lever length): 55 mm · Ø screw holder: 6.5 mm · Cranking (offset): 8 mm
EUR 85.50
swiing® revival rear brake anchor plate | Puch Maxi N
Total length: 135 mm · Manufacturer: swiing® revival parts · Surface: galvanized (blue) · Material: Steel · Ø External brake pads: 80 mm · Ø axle: 12 mm · Ø bore: 12.2 mm · Ø screw holder: 6.5 mm · Ø shaft: 10 mm · Wide cam holder: 12 mm · Ø outside: 92 mm · Brake lever length (lever length): 68 mm · Cranking (offset): 10 mm
EUR 91.60
Not in stock
Magura set screw M6x34 mm lock nut SW10
Manufacturer: Magura · Width across flats nut: 10 mm · Material: Brass · Surface: nickel-plated · Ø cable holder: 3.05 mm · Thread type: M6x1 (standard thread) · Slotted: No · Ø Receptacle: 7.05 mm · Thread length: 23 mm · Width across flats Screw: 8 mm · Total length: 34 mm
EUR 3.05
swiing® revival wheel axle M12x1 x 185 rear (closed ball bearing) | Puch
Material: Steel · Surface: galvanized (blue) · Manufacturer: swiing® revival parts · Total length: 185 mm · Thread type: MF12x1 (fine pitch thread) · Thread length: 28 mm · Thread length: 52 mm · Width across flats SW: 7 mm · Shank length: 99 mm · Ø shaft: 11.95 mm
EUR 12.10
SKF 16101 2RS1 ball bearing 12/30/8
Material: Plastic · Manufacturer: SKF · Material: Steel · Surface: blank · Width: 8 mm · Bearing cage: "-" Sheet steel cage ball-guided · Inner ring width: 8 mm · Dust protection type: 2RS1 - NBR contact seal on both sides · Bearing clearance: CN (standard) · Groove ring: No · Area of application: Standard · Stock number: 16101 · Bearing type: Deep groove ball bearing · Ø inside: 12 mm · Ø outside: 30 mm · Ball bearing closed: Yes
EUR 19.90
Moped fans like you also bought:
GPO 38 mm cylinder head original | Puch Maxi S, N / X30 NS, NL, N-2AH
Manufacturer: GPO · Area of application: Standard · Material: Aluminum · Surface: sandblasted · Width: 125 mm · Height: 55 mm · Total length: 135 mm · Ø cylinder: 38 mm · Number of fixing points: 4 pcs · Candle thread: short · Hole pattern [mm]: 44 x 44 · Decompressor: No
EUR 40.20
GPO 17" spoke set incl. nipple (2.9 x 188 mm) Inox
Manufacturer: GPO · Material: Chrome steel (known as Nirosta®) · Quantity: 36 pcs · Surface: raw · Color: silver · Length from hook: 188 mm · Ø spoke: 2.9 mm · Ø spoke head: 5.35 mm · Nominal diameter (thread): 3.15 mm · Thread length: 11 mm · Nipple length: 14 mm · Ø nipple head: 7.9 mm · Ø Nipple neck: 5 mm · Hook length: 9 mm · Hook angle: 95 °
EUR 67.20
swiing® ingenious wheel axle with bearing conversion kit spoke hub front Ø 29 mm | Puch
Manufacturer: swiing® ingenious parts · Material: Steel · Surface: galvanized (blue) · Thread type: MF12x1 (fine pitch thread) · Ø shaft: 11.95 mm · Ø outside: 29.02 mm · Ø inside: 12 mm · Total length: 165 mm · Thread length: 40.5 mm · Thread length: 50 mm · Shank length: 74.5 mm · Width: 2.7 mm · Width: 6.6 mm · Width: 11 mm · Width: 35.7 mm · Height: 5.9 mm · Height: 9.9 mm · Width across flats SW: 19 mm · Ball bearing closed: Yes
EUR 47.60
swiing® revival rear brake anchor plate | Puch Maxi S, X30 NG
Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Ø outside: 91 mm · Ø shaft: 10 mm · Ø External brake pads: 80 mm · Ø bore: 12.2 mm · Total length: 187 mm · Ø axle: 12 mm · Wide cam holder: 12 mm · Brake lever length (lever length): 55 mm · Ø screw holder: 6.5 mm · Cranking (offset): 8 mm
EUR 85.50
Collection only possible with online purchase and appointment.
