Pinasco «EVOTEN BIG BORE» cylinder with 46 mm bore and 71 cc for your Piaggio Ciao, Si, Bravo, Boxer, Grillo moped / moped.
The completely reworked 46 mm cylinder from Pinasco is now supplied with a 6-channel layout and the 5-fold bolted cylinder head manufactured for the highest loads.Various racing exhausts can be fitted to the supplied exhaust flange with 22.5 mm outer connection diameter.
The cylinder head is fitted without gasket. For optimum sealing, the tightening torque of 10 Nm for the M6 bolts and 14 Nm for the M7 stud bolts must therefore be observed.
The following parts are included in the scope of delivery:
- Additional screws for the cylinder head
- Decompressor valve (actuation not included)
- Cylinder head empty
- Cylinder and accessories
- Piston with L-ring, rectangular ring and Ø 10 mm piston pin (axe 10)
- Various gaskets for the cylinder base
- Installation instructions in Italian
High-quality cast aluminum and durable Nikasil coating characterize this high-end tuning cylinder.
The cylinder kit develops maximum power in the mid to upper rev range. We recommend using the racing cylinder in combination with a variomatic drive.
Mounting on an original engine housing is only possible with major modifications. The cylinder kit can be mounted on the well-known Pinasco, Polini and Malossi racing cases without any adaptation work.
Note: If the cylinder kit is mounted on a Piaggio Ciao, it must be ground down on the cooling fins on the right-hand side. Due to the cut-out for the Ciao's cable duct, the hook on the head for the decompression cable is also missing. As a result, the cylinder cover is only suitable to a limited extent for Piaggio Si, Bravo of the newer generations or Grillo. This can be remedied by attaching the decompression cable to the cylinder head from the front, as on the Ciao or Boxer.
Corresponding add-on parts such as racing gears, racing crankshaft, racing variator, etc. can be found in the accessories section.
Quality product from the Italian manufacturer Pinasco.
| Nominal diameter | 46 mm |
| Manufacturer | Pinasco |
| Material | Aluminum |
| Surface | varnished |
| Displacement | 71 ccm |
| Crankshaft stroke | 43 mm |
| Ø cylinder neck | 50 mm |
| Ø Outlet outside | 22.5 mm |
| Ø outlet inside | 18.5 mm |
| Ø piston pin (B) | 10 mm |
| Number of fixing points | 3 pcs |
| Outlet type | slanted, clamped |
| Hole spacing outlet | 48 mm |
| Thread outlet | M6x1 (standard thread) |
| Hole pattern [mm] | 55 x 34 |
| Decompressor | Yes |
| Camouflaged | No |
| Area of application | Tuning |
| Piaggio | Ciao - P, SC, PX, C24 Si Bravo / Super Bravo Boxer Grillo |
Ratings
Accessories & related products
swiing® ingenious needle roller bearing 12/15/16.2 "Racing" silver cage
Bearing cage: Silver cage · Manufacturer: swiing® ingenious parts · Bearing type: Needle roller and cage assembly · Width: 16.2 mm · Ø outside: 15 mm · Ø inside: 12 mm · Dimension needle bearing: 12/15 x 16.2 · Tomos OEM number: 035548
EUR 17.20
Not in stock
Polini Speed Engine engine housing electronic ignition | Piaggio Ciao, SI, Bravo, Boxer
Manufacturer: Polini · Material: Aluminum · Surface: sandblasted · Color: silver · Stock number: 6202 · Crankshaft stroke: 43 mm · Ignition type: Electronic · Total length: 215 mm · Width: 175 mm · Height: 104 mm
EUR 259.00
Polini Speed Engine engine case breaker ignition | Piaggio Ciao, SI, Bravo, Boxer
Color: silver · Total length: 215 mm · Height: 104 mm · Manufacturer: Polini · Material: Aluminum · Surface: sandblasted · Stock number: 6202 · Crankshaft stroke: 43 mm · Width: 175 mm · Ignition type: Breaker
EUR 259.00
Not in stock
Malossi MP-One engine case electronic ignition | Piaggio Ciao, SI, Bravo, Boxer
Color: silver · Total length: 220 mm · Height: 174 mm · Manufacturer: Malossi · Material: Aluminum · Surface: sandblasted · Width: 104 mm · Ø inside: 24 mm · Ø outside: 140 mm · Ignition type: Electronic
EUR 283.70
Not in stock
Pinasco flywheel "Flytech" Carbon | Piaggio Ciao, SI, Bravo, Boxer
Manufacturer: Pinasco · Material: Aluminum · Material: Carbon · Surface: varnished · Ø Internal flywheel: 106 mm · Direction of rotation: right · Weight: 650 g · Ø cone small inside: 12.4 mm · Ø cone large inside: 14.5 mm · Ø Flywheel outside: 135 mm · Cone length: 12.5 mm · Thread type: MF16x1 (fine pitch thread) · Cone ratio: 1:5 · Height: 38.7 mm · Thread length: 7.5 mm
EUR 259.00
swiing® revival stud bolt set M7x120 mm cylinder | Piaggio Ciao, SI, Bravo, Boxer
Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Diameter: 6.2 mm · Thread type: M7x1 (standard thread) · Drive: External hexagon · Total length: 120 mm · Width across flats: 11 mm · Thread length: 25 mm · Strength class: 8 · Strength class: 8.8
EUR 14.40
swiing® ingenious stud bolt M7x120 / Ø 7.3 shank (10.9 strength)
Manufacturer: swiing® ingenious parts · Diameter: 7.3 mm · Material: Steel · Surface: galvanized (blue) · Thread type: M7x1 (standard thread) · Thread length: 20 mm · Thread length: 30 mm · Total length: 120 mm · Strength class: 10.9
EUR 6.05
Moped fans also bought
Cuppini handlebar Ø 21 mm with stem 23.5 cm | Piaggio Ciao
Color: Chrome · Height: 260 mm · Manufacturer: Cuppini · Material: Steel · Surface: chrome-plated · Width: 600 mm · Ø outside: 22 mm · Mounting type: Front boom mounting · Ø Stem: 21 mm · Stem height: 160 mm · Length handlebar ends: 160 mm · Crossbar: No
EUR 86.30
swiing® revival luggage carrier clamp set | Piaggio Ciao PX, C24
Manufacturer: swiing® revival parts · Material: Chrome steel (colloquially known as stainless steel) · Material: Plastic · Material: Steel · Surface: chrome-plated · Surface: stainless · Piaggio OEM number: 013880 · Piaggio OEM number: 031087 · Piaggio OEM number: 188117 · Piaggio OEM number: 188119 · Piaggio OEM number: 188957 · Piaggio OEM number: 191461 · Piaggio OEM number: 195482 · Piaggio OEM number: 216738
EUR 98.60
Collection only possible with online purchase and appointment.
