Pinasco “EVOTEN” cylinder with a 42 mm bore and 60 cc displacement for your Piaggio Ciao, Si, Bravo, Boxer, or Grillo moped.
The completely redesigned 42 mm cylinder from Pinasco now comes with a 5-channel layout and a cylinder head secured with five bolts, engineered to withstand the toughest conditions. Various racing exhausts can be mounted to the included exhaust flange, which has an outer connection diameter of 22.5 mm.
The cylinder head is installed without a gasket. To ensure an optimal seal, it is therefore essential to strictly adhere to the tightening torque of 10 Nm for the M6 screws and 14 Nm for the M7 studs.
The following parts are included in the delivery:
- Additional bolts for the cylinder head
- Decompression valve (actuator not included)
- Empty cylinder head
- Cylinder and accessories
- Piston with L-ring, square ring, and 12 mm piston pin (axe 12)
- Various gaskets for the cylinder base
- Installation instructions in Italian
High-quality cast aluminum and a durable Nikasil coating characterize this high-end tuning cylinder.
The cylinder kit delivers its maximum power in the mid- to high-rpm range. We recommend using the racing cylinder in combination with a variator drive.
Installation on an original engine case is only possible with minor modifications. The cylinder kit can be installed on the well-known Pinasco, Polini, and Malossi racing cases without any modifications.
Note: If the cylinder kit is installed on a Piaggio Ciao, the cooling fins on the right side must be sanded down. However, due to the recess for the Ciao’s cable channel, the hook on the head for the decompression cable is also missing. As a result, the cylinder head is only partially compatible with newer-generation Piaggio Si, Bravo, or Grillo models. This can be resolved by routing the decompression cable to the cylinder head from the front, as is done on the Ciao or Boxer. Please observe the installation direction during assembly. The piston is installed with the arrow pointing toward the exhaust port on the exhaust side.
You can find corresponding components—such as racing casings, racing crankshafts, racing variators, etc.—in the accessories section.
Manufactured by the Italian brand Pinasco.
| Nominal diameter | 42 mm |
| Manufacturer | Pinasco |
| Material | Aluminum |
| Surface | varnished |
| Displacement | 60 ccm |
| Crankshaft stroke | 43 mm |
| Ø Outlet outside | 22.5 mm |
| Number of fixing points | 3 pcs |
| Ø piston pin (B) | 12 mm |
| Outlet type | clamped |
| Decompressor | Yes |
| Camouflaged | No |
| Area of application | Tuning |
| Piaggio | Ciao - P , SC , PX , C24 Si Bravo / Super Bravo Boxer Grillo |
Accessories & related products
swiing® ingenious needle roller bearing 12/15/16.2 "Racing" silver cage
Bearing type: Needle roller and cage assembly · Bearing cage: Silver cage · Dimension needle bearing: 12/15 x 16.2 · Manufacturer: swiing® ingenious parts · Ø inside: 12 mm · Width: 16.2 mm · Ø outside: 15 mm · Tomos OEM number: 035548
EUR 17.00
Polini Speed Engine engine housing electronic ignition | Piaggio Ciao, SI, Bravo, Boxer
Stock number: 6202 · Width: 175 mm · Height: 104 mm · Manufacturer: Polini · Material: Aluminum · Surface: sandblasted · Color: silver · Crankshaft stroke: 43 mm · Ignition type: Electronic · Total length: 215 mm
EUR 257.30
Polini Speed Engine engine case breaker ignition | Piaggio Ciao, SI, Bravo, Boxer
Stock number: 6202 · Width: 175 mm · Height: 104 mm · Manufacturer: Polini · Material: Aluminum · Surface: sandblasted · Color: silver · Crankshaft stroke: 43 mm · Ignition type: Breaker · Total length: 215 mm
EUR 257.30
Pinasco flywheel "Flytech" Carbon | Piaggio Ciao, SI, Bravo, Boxer
Height: 38.7 mm · Manufacturer: Pinasco · Material: Aluminum · Material: Carbon · Surface: varnished · Weight: 650 g · Thread type: MF16x1 (fine pitch thread) · Direction of rotation: right · Ø cone small inside: 12.4 mm · Ø Internal flywheel: 106 mm · Ø cone large inside: 14.5 mm · Ø Flywheel outside: 135 mm · Cone length: 12.5 mm · Cone ratio: 1:5 · Thread length: 7.5 mm
EUR 257.30
swiing® revival Stud Bolt Set M7x120 Cylinder | Piaggio Ciao, SI, Bravo, Boxer
Diameter: 6.2 mm · Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Thread type: M7x1 (standard thread) · Nominal diameter (thread): 7 mm · Drive: External hexagon · Width across flats: 11 mm · Total length: 120 mm · Thread length: 25 mm · Strength class: 8 · Strength class: 8.8
EUR 14.30
swiing® ingenious stud bolt M7x120 / Ø 7.3 shank (10.9 strength)
Diameter: 7.3 mm · Manufacturer: swiing® ingenious parts · Material: Steel · Surface: galvanized (blue) · Thread type: M7x1 (standard thread) · Total length: 120 mm · Thread length: 20 mm · Thread length: 30 mm · Strength class: 10.9
EUR 6.00
Explore categories from Cylinder
Moped fans also bought
GPO ignition plate 6 / 12V CDI ignition
Ø inside: 18.5 mm · Ø outside: 90 mm · Manufacturer: GPO · Material: Aluminum · Material: Copper · Material: Plastic · Material: Steel · Ø bolt circle: 80 mm · Number of fixing points: 4 pcs · Ø Internal flywheel: 90 mm · Number of cables: 2 pcs · Tension: 6 V · Tension: 12 V · Cable length: 580 mm · Area of application: Performance · Area of application: Standard
EUR 110.20
Polini cylinder head for 38.4 - 43 mm cylinder | Piaggio Ciao, SI, Bravo, Boxer
Width: 85 mm · Height: 58 mm · Manufacturer: Polini · Material: Aluminum · Camouflaged: No · Ø cylinder: 38.4 - 43 mm · Area of application: Tuning · Candle thread: long · Total length: 118 mm · Decompressor: Yes
EUR 67.30
Working late? Evening hours on Thursday until 20:00
